Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has a lot going for it. It looks smart, drives well and has a big boot. Can it compete in the most competitive segment of the market perhaps?
If your Peugeot key fob is not functioning, it might have been exposed to clean tap water or soapy water. You may have to remove the battery and clean it using electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs are equipped with small coin batteries that powers their remote locking and other features. The battery is limited in lifespan and is susceptible to wear after a long period of usage. Voltage testing is an easy method to determine if the battery is defective. Multimeters can be used to measure voltage between the poles that are plus and minus of the battery. The results of this test will indicate whether the battery is dead or not.
If you've been using your Peugeot 3008 for a while, and your key fobs have stopped working, there may be an issue with the receiver module. The receiver module is responsible for receiving radio frequency signals generated by key fobs and sending them out to the car's systems. If the receiver module malfunctions and not functioning properly, it won't be able to relay commands to the other modules inside the vehicle.
Moisture or sweat that gets on the circuit board is another frequent reason for a malfunctioning key fob. It can trigger short circuits, which will cause the battery to be depleted and disable the fob's remote locking feature. If this is the case you must bring your key fob into a chip level technician to repair it.
Water damage
If you dropped your key fob into the pool, threw it in the washer or even left it in the rain for too long, water damage could cause a lot of problems. Water is a great conductor, and it can also damage the components of the circuit board. It can also cause corrosion to metal lines on the key fob as well as other components. A wet circuit board can also cause the battery discharge its charge.
If you have an extra key fob, try using it to unlock or lock your Peugeot 3008 to rule out the possibility that a dead coin battery is the root of the problem. Another issue that could stop your key fob from functioning properly is interference signals that interfere with the signal sent to the receiver module. These signals of interference are generated by various sources such as radio transmitters within the vicinity.
If you hear sloshing noises emanating from your Peugeot 3008 when driving it is most likely caused by a blocked condensate drain from the evaporator. You can test this by blowing compressed air into the drain holes under your door. You can also use a flexible wire to make the drain holes sway and dislodge any dirt that might have collected there. The sloshing sounds can also indicate that there are air pockets in the cooling system.
A malfunctioning receiver module
The receiver module of the Peugeot 3008 key fob is responsible for transferring the remote keyless system signal from the key fob to the car's receiver. The receiver module may be damaged and stop the car from accepting your key fob. Other reasons that could cause this issue include an unresponsive battery or water damage, as well as interference from electronic devices that operate at the same frequency the key fob. In these situations an error message such as "card not detected" may appear on the display.
Luckily, there are a number of ways to troubleshoot this issue. Try replacing the battery or reprogram the key fob. You can also make use of a spare key to start the car. However, if the key fob doesn't work after all these steps, it may have a chip that is faulty.
The best way to determine whether the key fob is equipped with damaged chip is to take it off and clean it with a paper towel and rubbing alcohol. If the chip is damaged, you must purchase an entirely new one. The FB Series enclosures come with an holder for coin cells that can be used with the most popular kinds of key fob batteries. The enclosures can be personalized using digital printing and CNC-machined cutouts. If your key fob was exposed to salty or dirty tap water, it's possible that the chip has been infected.
Keyless entry systems with malfunctions
If you get "card not detected" This indicates that your vehicle isn't receiving a signal sent by your key fob. This can be due to many reasons including the battery being weak or dead. The problem can often be resolved by pressing the start button on the key fob. In certain cases, you might have to take the keyfob to an Peugeot dealer for repairs.
The first step in identifying the cause of a Peugeot 3008 key fob that won't unlock or lock the doors is to test the battery. Batteries are the most frequent reason for a fob that is malfunctioning but there are other factors that cause this issue as well. These include worn buttons as well as water damage.
If your Peugeot key fob has been exposed to clean tapwater, it's a good idea for you to take the battery off. Then, dry the electronic components using paper towels. You can also make use of a cleaner or isopropyl ethanol for this. If the fob has been exposed to salt or soapy water, it's best to replace it.
If your key fob is not working, you can try to reset it by disconnection of the 12 volt battery for about 15 minutes. Connect peugeot car key , and then the positive cable.